#------------------------------------------------------------------------ # Domain File # Original Author(s): Roberto Padilla-Hernandez,Douglas Gaer # Alex Gibbs, Pablo Santos,Tony Freeman # File Creation Date: 06/01/2012 # Date Last Modified: 05/11/13...ag # # Version control: 1.33 # # Support Team: # # Contributors: # # ----------------------------------------------------------------------- # ---------------------- Description and Details ------------------------ # ----------------------------------------------------------------------- # # File used to setup a geographical domain for SWAN and WW3 # # ----------------------------------------------------------- #======================================================================== # TBW = # GEOGRAPHICAL DOMAIN, GEOGRAPHICAL RESOLUTION AND OUTPUT TIME STEP = # = # NOTE: RES = spatial resolution in km = # TSTEP = request output time step (not the model time step) = #======================================================================== # export SITEID="TBW" export REGIONID="SR" export NELAT="29.70" export NELON="-81.50" export SWLAT="25.45" export SWLON="-84.80" export RES="1.8" export TSTEP="3" # #======================================================================== # NESTED GRID CONFIGURATION = # = # These nested grids are non-telescopic grids (i.e all of them are = # nested in the outer grid, and get the boundary conditions only from it) = # Later versions of NWPS will either allow for telescopic nesting or = # will be run on an unstructured grid characterized with a fine mesh = # over the nearshore zones and a coarser mesh across the offshore areas. = # = #======================================================================== # # TO DO: Update the domains below to reflect the area/s that you are # interested in (must reside inside of you outer domain defined # above). Also, remember to remove or comment out the remaining # example nests below that were configured for another area. Once # your nests are configured, just toggle the NESTGRIDS to '1' # (Default configuration is off or '0') and you will have control # from the GFE GUI to activate your nests during your runs. # # STATIONARY VS NONSTATIONARY MODE: # # STATN=STA for STATIONARY RUNS, STATN=NON for NON-STATIONARY RUNS. # The default value is NONstationary for CG1 (outer grid) and STAtionary # for the nested grids. Change this only if you know what you are doing. # You can choose STA or NON for a particular nested grid. In general, # if your domain that you define as a nest below is >= 100 km^2, then # set STATN=NON. For the very small domains or nests (<= 100 km^2) # set STATN=STA. # # ACTIVATE NEST/S: default is on for TBW # # NESTGRIDS="0" ... turns off nest options # NESTGRIDS="1" ... turns on nest options # export NESTGRIDS="1" export NESTINCG1="YES" # # NEST 1...grid matches bathy 1 arc-sec (~30m res) NAVD 88 DEM from NGDC export NELATN1="28.05" export NELONN1="-82.38" export SWLATN1="27.48" export SWLONN1="-83.20" export RESN1=".350" export TSTEPN1="3" export STATN1="NON" # # #======================================================================== # SPECTRA OUTPUT LOCATIONS # = # NOTE TO USER: the lat/lon points specified can be changed for any = # arbitrary point of interest within your outer domain defined above. = # One default buoy locations has already been configured for you = # below. Add more as needed. = # # NOTE: These do not have to match NDBC locations. = # #======================================================================== # Spectra points defined as space delimited list of: # "name1:lat1:lon1 name2:lat2:lon2 name3:lat3:lon3 name4:lat4:lon4 ...." # export SPECPOINTS="42021:28.311:-83.306 42036:28.500:-84.517 42013:27.169:-82.926" # #======================================================================== # WAVE TRACKING (and WAVE PARTITION) ON/OFF = # SET: SUBDOTBWN, GEOGRAPH RESOL and TOLERANCE WAVETRACK PARAMETERS = #======================================================================== # IF WAVE TRACKING IS REQUIRED THEN WVTRCK="ON", OTHER WISE SET IT AS "OFF" # IF WVTRCK IS "ON", ADDTIONAL INFORMATION IS REQUIRED, SEE BELOW # export WVTRCK="ON" # # IF WAVE TRACKING IS REQUIRED EXACTLY OVER THE COMPUTATIONAL GRID AND SAME SPATIAL # RESOLUTION: SET WVTONCG="1" # IF USER WANTS TO CHANGE ANYONE OF THE PARAMETERS THEN WVTONCG="0" AND USER MUST GIVE # ALL INFORMATION FOR THE DOMAIN OR SUBDOMAIN AND GEOGRAPHICAL RESOLUTION. # BE CAREFULL, IF THERE IS ANY SPECTRAL OUTPUT LOCATIONS OUT OF THE NEW (REDUCED) DOMAIN # FOR WAVE TRACKING NWPS WILL ABORT. # (This will be changed in a new version, the user can get 1d-spectra but not g-h plots). # export WVTONCG="0" export NELATWT="29.70" export NELONWT="-81.50" export SWLATWT="25.45" export SWLONWT="-84.80" export GEORESWT="4.0" # # PARAMETERS FOR TRACKING ALGORITHM for WVTONCG=0 or =1 THIS IS ALWAYS READ # *CAUTION* CHANGE THEM ONLY IF YOU KNOW WHAT YOU ARE DOING # RECOMENDED VALUES WVTRKPA="10. 1. 0.25 0.1 10. 1." # dirKnob, perKnob, hsKnob, wetPts, dirTimeKnob, tpTimeKnob export WVTRKPA="10. 1. 0.25 0.1 10. 1." # #======================================================================== # CURRENTS DEFINITION (SEE SWAN MANUAL) = #======================================================================== #export CURRL1="INPGRID CUR ............................." #export CURRL2="READINP CUR ............................." # #======================================================================== # BOUNDARY CONDITIONS (SEE SWAN MANUAL) = #======================================================================== # IF BOUNDARY CONDITIONS WILL BE USED then BOUNDCOND=1, Otherwise =0; # Setting up BOUNDCOND here to zero will permanently disable BCs. # If you leave it as 1 the user will still have the option to disable # them from the interactive Run_NWPS GUI. # export BOUNCOND="1" export FTPPAT1="multi_1" export FTPPAT1B="multi_1" export FTPPAT2="TBW" export NFTPATTEMPTS="3" export WAVECPS="multi_1.TBW59.spec.swan" # # THE FOLLOWING LINES MUST BE COMMENTED. IF YOU ADD BOUNDARY COMMAND LINES FOR YOUR # DOMAIN, ADD THEM WITH THE "#" AS A FIRST CHARACTER, IF YOU DECIDE NOT TO USE BOUNARY # CONDITIONS (BOUNCOND="0") THEY WILL REMAIN AS A COMMENTED LINES. IF YOU DECIDE TO USE # BOUNDARY CONDITIONS (BOUNCOND="1") NWPS WILL INCLUDE THE INFORMATION IN THE ACTUAL # INPUT FILES WITH NOT COMMENT CHARACTER # #$BOUNDARY COMMAND LINES #$southern side TBW - east to west #BOUN SEG XY 277.7 25.45 275.2 25.45 VAR FILE 0.00 'multi_1.TBW64.spec.swan' 1 & # 0.50 'multi_1.TBW63.spec.swan' 1 & # 1.00 'multi_1.TBW62.spec.swan' 1 & # 1.50 'multi_1.TBW61.spec.swan' 1 & # 2.00 'multi_1.TBW60.spec.swan' 1 & # 2.50 'multi_1.TBW59.spec.swan' 1 #$western side TBW - north to south #BOUN SEG XY 275.2 29.45 275.2 25.45 VAR FILE 0.00 'multi_1.TBW51.spec.swan' 1 & # 0.50 'multi_1.TBW52.spec.swan' 1 & # 1.00 'multi_1.TBW53.spec.swan' 1 & # 1.50 'multi_1.TBW54.spec.swan' 1 & # 2.00 'multi_1.TBW55.spec.swan' 1 & # 2.50 'multi_1.TBW56.spec.swan' 1 & # 3.00 'multi_1.TBW57.spec.swan' 1 & # 3.50 'multi_1.TBW58.spec.swan' 1 & # 4.00 'multi_1.TBW59.spec.swan.cp' 1 #$ #$END BOUNSEG # #======================================================================== # RIP CURRENT PROGRAM (SEE NWPS MANUAL) = #======================================================================== # IF RIP CURRENT PROGRAM WILL BE RUN, then RIPCONT=1, Otherwise =0; # Setting up RIPCONT here to zero will permanently disable RIP program. # export RIPPROG="1" export RIPDOMAIN="CG2" export RIPCONT="5m" # #___________________________________________________________________________ # RAY Section: Define a pair of rays to drop data out along critical contours # for rip current program. # # Example: for data output every 2km along a 5m bathy contour # # RAY 'rayname' xp yp xq yq int xp yp xq yq # # RAY 'ray1' 282.85 34.628 282.85 34.62 2000 283.00 34.655 283.00 34.62 # # ISOLINE '5mcont' 'ray1' BOTtom 10 # TABLE '5mcont' HEAD '5mtable' HSIGN TPS PDIR OUTPUT 20110825.1200 3.0 HR #_____________________________________________________________________________ # # THE FOLLOWING LINES MUST BE COMMENTED. IF YOU ADD RIP COMMAND LINES FOR YOUR # DOMAIN, ADD THEM WITH THE "#" AS A FIRST CHARACTER, IF YOU DECIDE NOT TO USE RIP # CURRENTS (RIPCONT="0") THEY WILL REMAIN AS A COMMENTED LINES. IF YOU DECIDE TO USE # BOUNDARY CONDITIONS (BOUNCOND="1") NWPS WILL INCLUDE THE INFORMATION IN THE ACTUAL # INPUT FILES WITH NOT COMMENT CHARACTER # POIN '5mcont' 279.887 25.8725 # #$RIP LINES #$ Ray for 5m contour data. #$ #POINTS '5mcont' & #277.286 27.4897 & #277.280 27.4996 & #277.272 27.5091 & #277.260 27.5081 & #277.250 27.5126 & #277.240 27.5189 & #277.230 27.5253 & #277.225 27.5377 & #277.225 27.5432 & #277.231 27.6660 & #277.234 27.6758 & #277.241 27.6871 & #277.244 27.6987 & #277.247 27.7083 & #277.250 27.7133 & #277.241 27.7229 & #277.237 27.7326 & #277.225 27.7313 & #277.219 27.7423 & #277.212 27.7512 & #277.204 27.7585 & #277.205 27.7645 & #277.195 27.7715 & #277.202 27.7780 & #277.192 27.7869 & #277.182 27.7913 & #277.169 27.7967 & #277.163 27.8071 & #277.159 27.8168 & #277.150 27.8238 & #277.140 27.8254 & #277.140 27.8330 & #277.137 27.8460 & #277.131 27.8565 & #277.131 27.8686 & #277.131 27.8709 & #277.133 27.8816 & #277.142 27.8913 & #277.145 27.9043 & #277.148 27.9172 & #277.150 27.9275 & #277.150 27.9366 & #277.157 27.9431 & #277.157 27.9479 & #277.155 27.9593 & #277.153 27.9732 & #277.155 27.9852 & #277.155 27.9949 & #277.150 28.0074 & #277.154 28.0144 & #277.157 28.0237 & #277.160 28.0320 & #277.156 28.0435 #TABLE '5mcont' HEAD '5m_contour_CG2' TIME XP YP HSIGN TPS DIR DSPR VEL WATL WIND OUTPUT 20110825.1200 1.0 HR #$ #$END RIP # #======================================================================== # RUNUP PROGRAM (SEE NWPS MANUAL) = #======================================================================== # IF RUNUP PROGRAM WILL BE RUN, then RIPCONT=1, Otherwise =0; # Setting up RIPCONT here to zero will permanently disable RIP program. # export RUNUPPROG="1" export RUNUPDOMAIN="CG2" export RUNUPCONT="20m" # #___________________________________________________________________________ # RAY Section: Define a pair of rays to drop data out along critical contours # for rip current program. # # Example: SEE ABOVE FOR RIPCURRENT #_____________________________________________________________________________ # # THE FOLLOWING LINES MUST BE COMMENTED. IF YOU ADD RUNUP COMMAND LINES FOR YOUR # DOMAIN, ADD THEM WITH THE "#" AS A FIRST CHARACTER, IF YOU DECIDE NOT TO USE # RUNUP (RUNUPCONT="0") THEY WILL REMAIN AS A COMMENTED LINES. IF YOU DECIDE TO USE # IT NWPS WILL INCLUDE THE INFORMATION IN THE ACTUAL # INPUT FILES WITH NOT COMMENT CHARACTER # POIN '20mcont' 279.887 25.8725 # #$RUNUP LINES #$ Ray for 20m contour data. #$ #RAY 'ray2' 276.80 27.48 277.62 27.48 180 276.80 28.05 277.62 28.05 #ISOLINE '20mcont' 'ray2' BOTtom 20 #TABLE '20mcont' HEAD '20m_contour_CG2' TIME XP YP HSIGN TPS DIR VEL WATL WIND OUTPUT 20110825.1200 1.0 HR #$ #$END RUNUP #